A pressure switch is a device that senses changes in fluid pressure and responds in a specified way. An actuated pressure switch (a type of transducer) makes or disrupts electrical contact in order to either trigger an alarm or switch something on or off. Switches are programmed to activate at certain pressure points, and may be designed to make contact either on pressure rise or on pressure fall.
Pressure switches are specifically designed for alarm, shutdown, activation and pressure control of pneumatic and hydraulic processes and equipment, and thus work well in any instance in which regulation of flow is required. Utility plants, public buildings, process manufacturing, automotive and home appliance industries all use pressure switches extensively to regulate fluid pressure and to provide safety measures for high pressure applications.
Pressure switches are important for the safe and successful operation of a wide range of applications, such as: filters, furnaces, industrial heating systems, blowers, generators, cars, off-road equipment, compressors, turbines, space stations, wastewater applications, process equipment, pumps, panels and pipelines. Some batteries use pressure switches to prevent over-charging by switching off the charger when the internal cell pressure reaches a certain level. Pressure switches are especially useful in industrial facilities because they are a safe and cost-effective alternative to safety relief valves. Relief valves sometimes leak pressure during operation, wasting energy and in some cases causing a safety hazard, whereas use of pressure switches allows regulation of pressure at the source. Pressure switches can also accurately detect pressure problems and automatically shut down the process before the danger increases.
Pressure Switches – Tecmark Corporation
Pressure Switches – Ashcroft
Pressure Switches – Ashcroft
Pressure Switches – MAMCO Precision Switches
Pressure Switches – MAMCO Precision Switches
Ultra-low pressure switch – MAMCO Precision Switches
The History of Pressure Switches
The practice of pressure measurement as a whole began in the late the 16th century, with Galileo. In 1594, he obtained a patent for a water pump that used pressure in order to irrigate the land. Then, in 1644, Italian physicist Evangelista Torricelli created a sort of hermetically sealed vacuum tube with mercury. It was one meter long and he filled it with mercury by placing the open bottom end in a basin of mercury. Every time he filled the tube, it would fall precisely 760 mm, leaving space open at the top. Though it wasn’t sure of the cause, he named it a vacuum, bringing the world one step closer to understanding pressure switching. Just four years later, Blaise Pascal pinpointed the source of this force—the weight of the air above. He dubbed this force the name we know it by today, “pressure.” Throughout the rest of the 1600s, several different scientists and engineers conducted experiments concerning air pressure and how it can move items and elements. For instance, in 1661, Anglo-Irish chemist Robert Boyle studied the relationship between pressure and trapped gas using "J" shaped tubes that were closed at one end. After his experiment, he concluded that x V = K (P: Pressure, V: Volume, K: Constant). In other words, if you know the volume of a gas at a given pressure, you can calculate the pressure if the volume is changed, assuming that neither the temperature nor the amount of gas is changed.
Scientists used these building blocks to invent and develop pressure switches, starting in the 1800s. In 1843, French scientist Lucien Vidie invented and assembled the first aneroid barometer, which used a spring balance to measure atmospheric pressure. While under pressure, the spring extension would mechanically amplify on an indicator system. Based on Vidie’s methods, Eugene Bourdon patented the Bourdon tube pressure gauge in 1849. This was the well-known mechanical pressure measurement device, and it is still used today. From it, the basic concept of all electromechanical pressure devices, which use a sensing element like the Bourdon tube and a switch, are built. Mechanical pressure switches were the only type available until 1930, when engineers began experimenting with transduction mechanisms with sensing device movements as part of an electrical quantity. These were the first pressure transducers. Then, in 1938, engineers at the Massachusetts Institute of Technology and California Institute of Technology independently developed bonded strain gauges. They raced to the finish line, and E.E. Simmons of Caltech was the first to apply for a patent. The development of strain gauges was an important step in the right direction for solid-state pressure switches, which were widely introduced in 1980 by Barksdale Inc. At the time, they featured a bonded strain gauge sensor combined with a triac switch.
Today, solid-state pressure sensors are very popular and feature: digital displays, digital and analog outputs, full programmability and between one and upwards of four switch points. In the future, we believe that pressure switches will continue to become more intuitive and accurate.
Manufacturers generally assemble pressure switches with either some sort of mechanical sensing element and snap-action switch or an electronic output signal and programming interface. In the case of the latter, they also either factory program the system with predetermined switch points or install a programming interface that allows the user to program and adjust these switch points themselves and/or program a logic system that adjusts switch points and output signals intuitively. Programming interfaces feature integrated buttons and a LED or LCD digital display for ease of use.
Construction materials for pressure switches vary depending on the applications, but can include acetal, brass, polycarbonate, plated steel, glass reinforced polyester, polyvinyl chloride (PVC), cast aluminum, bronze, neoprene or stainless steel.
Design Considerations and Customization
When manufacturing pressure switches, manufacturers must consider a number of factors, including: required level of accuracy/sensitivity, cycle rates, adjustability and pressure(s) at which the switch must actuate. Pressure switches are always set to at least one point of pressure, or actuation point, to which it will automatically respond. Some switches are factory-set and cannot be changed, but there are also a variety of adjustable pressure switches available, which allow the user to adjust the actuation point or points. Many pressure switches work with several points of pressure, and are therefore able to act as more complex regulators of pressure systems.
The goal of the manufacturer is to make a pressure that is long lasting, durable, sufficiently accurate and easy to use. To do so, they can customize your pressure sensitivity, the speed at which the switch cycles, the number of cycles it performs before getting fatigued, its number of actuation points and the pressure range at which it works best. Also, depending on the application, pressure switch manufacturers can set a pressure switch to automatically open or close to interrupt or to initiate the flow or current involved.
Pressure switches can sense changes in gas and/or liquid pressure. Pressure switches sense pressure in a variety of ways. Some switches use a pressure sensor that reacts to changes in the pressure level, and actuates either a mechanical switch or a valve. Others work in conjunction with a pressure transducer, also known as a pressure transmitter, and a display meter. In the case of the former, mechanical (electromechanical) pressure switches, the actuated switch will move to be in direct contact with the fluid. To assist its movements, the switch also has a pre-set or user adjustable switch point. The latter, known as electronic pressure switches or solid-state pressure switches, usually make use of a piezoresistive pressure sensor that measures the pressure level and converts the level into an electrical signal. They are more common than the former.
Pneumatic Pressure Switch
Pneumatic pressure switches, also known as air pressure switches or gas pressure switches, are designed to sense and respond to gas pressure.
A common air pressure switch variety is the air compressor switch. Air compressor pressure switches signal to the compressor when more pressure is needed, when optimal pressure has been reached, and also when there is inadequate air supply for the suction stage.
Hydraulic Pressure Switch
Hydraulic pressure switches operate in response to liquid pressure. Examples of hydraulic pressure switches include well pump pressure switches, water pressure switches, oil pressure switches, ultrasonic level switches and displacer level switches.
Both well pump pressure switches and water pressure switches regulate water pressure by actuating a flow of water when pressure drops below a certain level and stopping the flow when the system reaches its optimal pressure. Oil pressure switches are used in cars to monitor the engine's oil pressure and to signal when the oil pressure has gotten critically low.
Ultrasonic level switches are ideal for use in tanks that store mass quantities of liquid, since they are unaffected by large changes in pressure and temperature; they also have no moving parts and therefore have no problems with sediment. Displacer level switches maintain the level of liquids in a sump based on a set point. Displacer level switches are low cost, simple to operate, easy to adjust and reliable.
Furnace Pressure Switch
Different sorts of furnace pressure switches either monitor for an adequate supply of fuel or monitor the furnace's supply of fresh air.
Differential Pressure Switch
Differential pressure switches help regulate differential pressure between a cavity and an open atmosphere, such as the pressure between an airplane cabin and the outside atmosphere. Note: Differential pressure is pressure measured relative to the pressure in the surrounding atmosphere. This pressure is measured in psi by a differential pressure gauge.
Vacuum switches help regulate the pressure between two closed cavities by responding to changes in negative pressure.
Diaphragm Pressure Switch
Diaphragm pressure switches are mechanical switches that use an elastomeric diaphragm to react to changes in the pressure level, and actuate either a mechanical switch or a valve, such as a solenoid valve.
Pressure Sensitive Mat
A pressure sensitive mat is a literal mat that provides a contact signal when you apply force to it. Pressure sensitive mats can provide either just one signal or several. They are used as a part of an interlock system in potentially dangerous machine operating areas, as a means to open electrically operated doors or to detect entrance into a space (for security, attendance count, etc.).
Advantages of Pressure Switches
Pressure switches are excellent and necessary devices for a number of applications for a number of reasons. First and foremost, they make processes involving pressurized fluids safe and dependable. They are also quite user friendly and easy to operate. This is particularly true of electronic pressure switches. In addition, pressure switches are serviceable for a wide range of applications with widely different pressure levels, system sizes, environments and requirements.
Accessories in which you may be interested include: audible alarms, delay relays and solid-state relays.
A major contributor to pressure switch standard literature in the United States is NEMA, or the National Electrical Manufacturers Association. NEMA releases standard ratings that offer insights about: safety, performance, construction, composition, tolerances, etc. It’s definitely a good idea to seek a manufacturer that uses verified NEMA ratings for their products. In Europe, it’s more common to work with IP (Ingress Protection) and/or CE (Conformité Européene). It may also be in your best interest to look for a switch with a UL safety rating that matches your application. No matter, it’s important that you make sure your pressure switch has been tested and verified for safety and performance. The standards mentioned above provide you a good way of knowing that. Often, your industry also requires certain certifications. Before you agree to work with a pressure switch manufacturer or supplier, make sure you know those requirements, and that the supplier can meet them.
Things to Consider
Some things to consider and evaluate when looking for a pressure switch are accuracy, electrical output, temperature compensation, temperature output and the material to be handled. Also important are operating temperature and capacity to operate with vibration and shock. In addition to these technical considerations, you must also make sure to partner with the right manufacturer. Who is the right manufacturer? The right manufacturer is the one who will listen carefully to your requirements and requests, and make sure to do everything to deliver you the best product and experience possible. Find a contract manufacturer or supplier like that by browsing towards the top of this page, where we have our top picks listed.
Pressure Switch Types
- Adjustable pressure switches are field adjustable, meaning that the set points can be adjusted at the place of operation.
- Air compressor switch controls pressure on air compressors.
control air flow and pressure in response to pneumatic pressures.
are able to control the level in a sump of virtually any liquid. Their
setpoints can be easily and quickly adjusted in the field.
- High pressure switches have extremely high proof pressure limits so that they can function in pressure systems that reach high pounds per square inch (psig).
respond and actuate in situations of minute, small or reduced pressure.
measure or regulate the amount of or pressure of oil through volume,
velocity or mass.
have pressure sensors and send signals and information
to a remote controller and regulate pressure.
are used in lubrication storage vessels for rotating
equipment and will alert the operator if there is a risk of damage due
to pressure leaks.
measure and/or regulate water pressure in correlation with pumps, according
to a set point.
- Well pump pressure switches controls the water well pump through turning the pump on and off in response to rises or drops in pressure.
Pressure Switch Terms
A limit of how much deviation from the switch set point is allowed, measured
in points per square inch or as a percentage.
More Pressure Switches Information
exact pressure that actuates the snap-action switch to either open or
close the circuit.
a pressure actuated switch, the differentiation between the actuation
point and the re-actuation point.
– The range of pressure a switch encounters under normal conditions.
that surrounds a pressure switch.
– While a switch
element reverses itself, the amount of mechanical motion that is lost.
difference between a reference point and the actual pressure value.
A device that will open or close an electrical circuit when prompted by
the pressure sensing element.
– A device that measures
the quantity of product flowing through it. (http://www.yc-antibes.net/flow-meters/)
– The difference
of a switch’s response to increasing and decreasing pressure.
– A device which
measures the pressure built up in a closed system. (http://www.yc-antibes.net/pressure-gauges/)
part of the element that is moved when pressure is changed.
– A device
that converts pressure into an electrical signal. (http://www.yc-antibes.net/pressure-transducers/)
– The measured
consistency and accuracy of a pressure switch to operate at its setpoints.
– A valve that
uses a solenoid to control the valve. (http://www.yc-antibes.net/solenoid-valves/)
– A fast
transfer of contacts from one site to another. They can quickly open or
close a circuit.
– The changing
pressure that activates the pressure switch.
Pressure Switches Informational Video